We had never had a house built. We learned that we will probably never want to do it again to be honest. However, one of our complaints was that we saw a printed layout of our house before we moved out but I don't believe they ever even showed us how our house would be situated on that lot. (I know! We should have asked. But lesson learned!) We were getting what we thought was a huge lot. We were in a cul de sac lot and were paying extra because of it so we weren't really worried about the size of our yard. We walked on the lot before we signed the papers and it looked huge!! But, needless to say, we have a stupidly shaped yard. They placed our house so far back on our lot that we have a LONG driveway and long front side yards and well....a stupidly shaped backyard.
We walk right outside our back door and we have our neighbors fence smack in our face. Okay, well maybe it's like 9 feet away...but it's really close people!! With it being SO close most of our concern and problem is with toys and balls being thrown into other people's yard and when your neighbors aren't very friendly and their dogs are mean you don't really get anything back. *Sigh.
We also only have a stub of a patio which is like 2 feet by 3 feet wide. We've wanted to add a large concrete patio slab but after counting the cost we ended up building the shades first and making it have the 'feel' of a patio without the huge expense of a patio.
Plus, we've had these shades in our closet for the last 6 years!! I kid you not! My In-laws were shopping at Costco one time and knew we were searching for a good deal and it was the end of Summer in Phoenix and they got 3 on mark down for us. It was a great deal. Surely we'd use them, right? Well, we finally have these 6 years later and I want to show you how we did it.
My husband went to a local lumber yard and bought some 12 foot cedar posts. He paid a pretty penny and you should too because they are going to take a beating with the winds and the last thing you want is a shade breaking off and flapping dangerously around in a fierce storm.
He also rented a one man auger machine, which in reality takes two people really but that's what it's called. Along with that he got some Quikcrete bags to solidify the posts into.
With everything at hand we looked at the size of the shades and we wanted it to float evenly in the middle between the house and fence. It's been awhile since we put these in but I believe it ended up being about 3 fee we added on each corner. We put it at an angle, so it was slightly higher up on the house. We had a hard time figuring out how far apart to put the beams. We wanted to make sure we put enough room to be able to have length to tighten as the shade got pulled loose from wind and such but we also didn't want it to be too far apart and not have the shades provide adequate coverage. We didn't want three triangle spots of shade but rather as close to a unified shade as possible. We ended up setting the poles roughly 21 feet apart. As you'll see in the pictures it was enough to keep them from overlapping but we might have been able to get them a foot or two closer. But we're happy with how they turned out.
We used painter's tape on the fence to mark where to dig. Ryan and my brother set off to work digging the first hole. One thing to note here: make sure you know what your rented equipment can do, otherwise you might end up in a big mess. Enter mess....Ryan and Darren dug down the drill end really quickly into the ground. Now if the auger you rented had a reverse switch that wouldn't be a big deal but...ours didn't. The guys didn't realize that because of our hard clay based ground (which will be great for holding these poles up, but not great for working with it) they dug down so fast they didn't even give it a chance to pull up any dirt. They pretty much just drilled it into clay and there it was stuck...for the next 3 hours it took all of us to dig it out of the ground. So if you look really closely you'll see the the base of the the farthest post has a very wide concrete bottom.
So after learning from their lesson, they jammed out the last two poled in less than 30 minutes. They dug down about 30 inches my husband said, which is as far as this auger let them go pretty much. We probably would have gone down more if possible but with our hard ground it will (and has) held up fine. Instead of going so fast with the auger they put it in slowly and let the drill slowly pull out the clay as it went down. They had to pull it back up every so often because it wants to go down much faster than it should. So they drilled a little. Stopped. Pulled it back up, just to clean out the drill and then they put it back in to go down a little farther.
Now that you we had our holes they mixed the concrete bags with the water. While I held the post in the right spot using a level, Ryan was able to fill in all around the pole. It was such a deep hole we really didn't even have to prop up the poles from leaning. We kept checking them periodically but they never even tilted, which was awesome!
After your posts are set then you need to add the hardware to the top of the posts. My husband just went to the store and got what he needed. He got a cable tensioner with a hook and some eyes that he was able to mount on the posts. He also got a few wire cable clamps (one for each corner of the shade) I included some pictures so you can see the hardware and how he mounted them on.
Make sure to leave some slack on the rope and just use those small little nuts to tighten up and hold the extra rope. You need enough to hang on and pull so you can tighten the shade later. You can slowly clip off the excess if needed though, just don't cut too short!!
(This
is where you can see that little bolt which holds the extra string up
so you have slack to pull when you have to tighten later.)
Once you have the hardware on your post then attach your shades onto the top of the beams.
(This is the main central beam which holds the three shades.)
(Here is how the attachment looks on one of the side beams, with just one shade attached.)
At this point it's kind of a grab the ladder and hold up where the shade would go on the house and mark where it will look the best. We started with the middle shade because that gave us our control. We wanted the other shades to fit as closely to the middle one as possible.
(A view of the attachment to the house.)
(Another view of how it's attached to the house.)
The shades are angled slightly, so the mounts are raised a little bit higher on the house versus the posts. It makes it have a more open feel than if they were just flat.
After the middle one was set we started with one side shade at a time and pulled the rope to the best spot so there was as little gap as possible between the shades but we also didn't want them to rub. You can see in this photo the final placement of where the ropes were attached to the house.
After everything was adjusted and tightened we snapped a couple more photos.
Please note that you need to plan to tighten your shade after a couple days of good wind. The shade will loosen a lot after it finally gets pulled tight by the wind. My husband has gotten in a good habit of after a really bad storm he will tighten them back up again or he just plans to do it during the Summer.
We also added some strings of outdoor lights onto the shades. We just strung them up around the shade hardware and ziptied them onto where they wouldn't slip. We used 3 strands and had a bunch extra so we took off the extra bulbs and stapled it to the back of the last post. So you can't see it from the front at all.
Here are some more pictures to enjoy!
Well, I hope this has spurred you on to build your own sun shades. We enjoy the fact that it adds a patio feel without having to pay for the whole concrete slab. We recently bought a picnic table and put it underneath and enjoy our lunch outdoors sometimes now.
God Bless!
Heather Joy
Amazing work, I really appreciate you. Sun Shades Dubai
ReplyDelete